|
Farrukh_5 wrote: Is it possible to have these both available and running like a normal windows networking as if there was only one domain server networking?
What do you mean by running like a normal windows networking? You want both server could be able to communicate with each other while is has a difference network id? If so, you need to use router device to connect both network segment.
Farrukh_5 wrote: Both servers have, active directory, DNS, Application Services
Farrukh_5 wrote: if there was only one domain server networking?
As you mention, there is only one domain server but you also declare that your both server has both active directory... Active directory could only exist when you promote your standalone server to a domain controller. Could you clarify about what you mean?
|
|
|
|
|
I've installed active directory on both servers and both are domain controllers. so i have two different domains and domain controllers running in the network with different IP address scopte.
Both Servers are connected in to the same network (same wire netowrk)
---------------------------
http://www.idlsol.com
|
|
|
|
|
Farrukh_5 wrote: I've installed active directory on both servers and both are domain controllers. so i have two different domains and domain controllers running in the network with different IP address scopte
Ok, based on your previous post[^] you will need to have a router device which connect between these two network. Then you will be able to communicate from one network ID to another network ID.
|
|
|
|
|
Assuming that both are connected to the same physical network, then you would open network properties, go to tcp/ip, open advanced, and add the address for the other network i.e. 192.168.x.x
Then if you want to use data from one or the other set up trusts.
Cheers
|
|
|
|
|
I'm trying to install a MSI (LINQ preview in fact), but at some stage it
(unsuccessfully) try to upgrade the C# language service with the error
message:
=====
An error occured while applying security settings. Power Users is not a
valid users group.
=====
But the control panel\User Account don't mention it...
What could I do?
|
|
|
|
|
Super Lloyd wrote: I'm trying to install a MSI (LINQ preview in fact), but at some stage it
(unsuccessfully) try to upgrade the C# language service with the error
message:
=====
An error occured while applying security settings. Power Users is not a
valid users group.
Generally, power user also have the right to install an application on the computer. But in the above information, I think your application might require another built-in account with have a complete right to do anything the computer. The best way to do that is use the secondary logon (right click and choose run as command) with administrative account and set up an application.
Super Lloyd wrote: But the control panel\User Account don't mention it...
What do you mean from here? Please complete your description and try to ask a question again.
|
|
|
|
|
Hi,
Its automatically closing the windows which containing the text "virus" or "anti virus" . How can I recover my machine from virus infection. I cant format it. Because it contains my valuvable informations. Pls help me.
JIJO BABY - Lets Play C#
|
|
|
|
|
Try to start your computer in safe mode environment. And try to run anti-virus to scan for the virus name. If it is not possible, isolate your infection machine from the network and an go to another clean machine to access the internet to download any cleaning tool which is free for use. The purpose is try any method to detect the virus name. Once you got the virus name you could use google to search for the specifi method to clean the virus.
|
|
|
|
|
Hi,
We change now our network from Novell 5.0 to Windows 2000 server. We have printing problem, Our Application are based Dos(Clipper). How can we print from based dos software to printer that is connect to windows 2000 server ?
I learn my self
|
|
|
|
|
|
at a guess, the dos apps are printing to lpt1, instead of whatever windows uses to communicate with a network printer.
|
|
|
|
|
dan neely wrote: at a guess, the dos apps are printing to lpt1, instead of whatever windows uses to communicate with a network printer.
i'm sure you wanted to say this to mikobi, didn't you ?! 
TOXCCT >>> GEII power
[VisualCalc 3.0 updated ][Flags Beginner's Guide new! ]
|
|
|
|
|
|
My domaine name is SNCC-INTERNET and my server have the name SEM, the sharing printer name is HP8000:
When I write net use lpt1: \\sem\hp8000 I have this message ;
The pass word is invalid for \\sem\hp8000
Enter user's name of 'SEM'....
Enter user's password of 'SEM' after writing my username and password, as my password is blank I have this message "System error 5 occurred"
Access refused.
What to do exactly
I learn my self
-- modified at 5:18 Friday 12th May, 2006
|
|
|
|
|
|
ON Windows I print from my station to this printer, but on Dos, when I map (net use lpt1 \\sem\hp8000) i have this error. Why and what to do to make access to this printer
|
|
|
|
|
mikobi wrote: when I map (net use lpt1 \\sem\hp8000) i have this error.
Make sure that user name and password that you use to login has a right to install a device driver on your PC. Check it with your system administrator.
|
|
|
|
|
I have A computer SEM Where I install windows 2000 server( this computer is a server), then i install a printer shared as HP8000. From my station I install it on windows and I print from it, when I map it(Net use lpt1: \\sem\HP8000) i have a problem(access denied) . I don't understand.
Who can Help me . My user open also the server
I learn My self
-- modified at 2:26 Monday 15th May, 2006
|
|
|
|
|
I understand now, As I use Win Xp Workstation, when I loged in my computer with At this computer as option (not At domaine SNCC-Internet) i have see that I was not right to see the printer on the server. After correct that, IT works now when I am loged with At this computer option; but is I am loged with my domaine(SNCC-internet) I can't map LPT1. But there is same thing that i don't understand. When I am loged with Administrateur in my domaine, the map works.
I want to know what thing is incorrect with others users because all are administrateurs of my station?
|
|
|
|
|
Thanks for your help.
All things are reghit now. I understand now.
God bless you
|
|
|
|
|
mikobi wrote: I want to know what thing is incorrect with others users because all are administrateurs of my station?
You have a problem with user right on your computer. Whether all user are administrator on a local computer but you should know it might be a member of user group on your domain controller. Every user which belong to local computer or belong to domain controller has it own group which is used to define the responsibility, right or permission to access resource or manage the computer. For more information you should see windows help file or Microsoft documentation about the difference of user right of each group in windows (workgroup or domain).
|
|
|
|
|
Try adding the mode command. and run the whole thing as a script or batch file.
|
|
|
|
|
Hi,
Am trying to implement a encryption-decryption system beween, Windows and Linux. and am planning to implement it in .NET.
Plese guide me and suggest some references.
Thanks.
Manivannan
|
|
|
|
|
How to create group policy in Windows 2003 server
Ajai
|
|
|
|
|
What do you mean by create a group policies in windows 2003? Please give more detail explaination about your question. You want to create a new temple or you want to create your own policies and put it in group policies?
|
|
|
|
General 
News 
Suggestion 
Question 
Bug 
Answer 
Joke 
Praise 
Rant 
Admin 
Submit an article or tip
