|
is there anybody who can help me to and an additional ide controller to intel 195 motherboard.
i have connected 2 SATA HDD and 2 combo drives with my system, and i want to add an additional IDE to my system and my system is having only 1 IDE controller. is there any way yo increase IDE controller.
|
|
|
|
|
a PCI based IDE card. You might be hard pressed to find a plain one because most have the same low end raid setups as the mobos use. Any raid card that supports JBOD (Just a Bunch Of Drives) can be used as a normal IDE controller.
|
|
|
|
|
I had a Promise Ultra100 TX2 card in an old computer which only had ATA/33 on the motherboard (440BX chipset). That was a fine card. If you wanted to boot Windows 2000 or XP from it, though, you needed to supply Setup with a floppy disk with the drivers.
It's been discontinued but its replacement, the Ultra133 TX2[^] should still be available.
If you're going to start adding additional controllers, though, you should probably consider switching to SATA disks (where possible).
|
|
|
|
|
is there anyboby who can suggest me how to control electronic electricity kwh meter through computer or any other way.
|
|
|
|
|
vikramjeetpta wrote: ...is there anyboby who can suggest me how to control electronic electricity kwh meter
Like the one on the side of your house, or on the pole?
"Approved Workmen Are Not Ashamed" - 2 Timothy 2:15
"Judge not by the eye but by the heart." - Native American Proverb
|
|
|
|
|
Well, that's easy enough... Just turn every light and every other electric device ON inside your house and I'll bet the numbers on the meter will tick faster... Also, you can turn OFF every electric device in the house and the numbers will tick slower -- might even stop!
How's that for control?
|
|
|
|
|
Can a PCI card (Universal 3.3 volt) card be used in a PCIX slot?
|
|
|
|
|
I'm not sure, but my PCI-X card will work in a standard PCI slot, so I'd assume the reverse was true as well. IIRC PCI-X just added another 32 bits of datachannel and pumped the maximum clock speed.
|
|
|
|
|
hi i am thinking of buying a 3d accelerator / gpu for gaming
dont know much about them
can anyone please guide me which will be the best buy
thanks
|
|
|
|
|
|
thank you sir
|
|
|
|
|
|
thank you sir
|
|
|
|
|
Was hoping the hardware gurus could provide some insight into this comparison.
dual 15,000rpm drives setup with raid-0
vs
single SATA 10,000rpm drive with databurst cache
These will be used on a development machine for code compilation.
|
|
|
|
|
I doubt that RAID-0 of two 15000 rpm drive could be beat by a single drive.
Farhan Noor Qureshi
|
|
|
|
|
Well, I figured the dual raid-0 drives would be better. What I'm wondering, though, is how much better. i.e., if its only a minor improvement, it might not be worth the extra money to get the dual raid-0 drives.
|
|
|
|
|
|
Dave Calkins wrote: dual 15,000rpm drives setup with raid-0
vs
single SATA 10,000rpm drive with databurst cache
Depending on the drive... but generally single SCSI U320 single 15k runs at 87 MB/s, a RAID0 pulls about 140+MB/s. My fastest RAID0 was a 4 disk RAID0 of 15K U320 drives. It's average speed was 280 MB/s, and was a hardware RAID0.
A single 10k SATA runs at about 78 MB/s with RAID0 starting at 120 MB/s and going up.
_________________________
Asu no koto o ieba, tenjo de nezumi ga warau.
Talk about things of tomorrow and the mice in the ceiling laugh. (Japanese Proverb)
|
|
|
|
|
Just purchased:
* AMD Athlon X2 64 3800
* 450 watt power supply
* Corsair XMS2 TWIN2x1024A-6400 (2x512)
I put these components together using the stock AMD heatsink and fan. These are the only components attached at this point other than a keyboard and speaker and power button.
When I try to boot this to get to the BOIS, it just makes repeated long beeps (or could be a long beep and short beep very close together as a get a click in the middle of the long beep). The manual says it is a problem with RAM or MB, but they are new and have been reported as compatible. I tried a stick of KByte 512 DDR2 PC2/533/400 and it did the same thing.
The power supply was first connected by the 20 pin connector and the 4 plug 12v connector for the CPU. After this did not work, I tried adding the four plug extension to make the 24 pin plug and still no change.
Any ideas of what it could be besides dead parts? It is not like there is a lot of components, just MB, RAM and power.
Is there any way to determine the CPU is install correctly and functioning? The CPU dropped right in and seem to go easy.
|
|
|
|
|
Rocky Moore wrote: Any ideas of what it could be besides dead parts? It is not like there is a lot of components, just MB, RAM and power.
Either youi've got the RAM in the wrong slots, for instance in slots 3&4 instead of 1&2, or the RAM and/or sockets are bad. If replacing the memory does the same thing, you've probably got a bad motherboard.
I had two Gigabyte motherboards in last machine I built. Both of them exhibited problems where the machine would just hang a random. After replacing everything else in the machine (CPU, RAM, Video), I put the original stuff back in the machine and swapped the motherboard with an Asus. Worked like a charm. The machine has been running for two years straight without a single crash or lock up.
Dave Kreskowiak
Microsoft MVP - Visual Basic
|
|
|
|
|
I dread the thought of it, but I am thinking it may be the motherboard. Just wish there was a way to know the CPU is working correctly as it has a short window of RMA.
I first looked at the ASUS MBs but they did not have the features I need such as 4 IDE devices (have 3 I need to use) and 6100 built in video. Was amazed to see some MBs did not even come with LPT ports since one of my printers still only works via LPT.
Over the last three weeks I have dug through tons of information trying to what works with what, what is just overpriced and what is garbage. Additionally, what will work with Vista or at least to a point.
This upgrade adventure has at least taught me that the designers out there for hardware need to be whipped daily as the industry has become far to complicated. In the old days, you needed RAM, you purchased some of the speed you needed and presto it worked. Now it depends on vendor, volts and other things. Then there is the different CPU socket types and chip sets, along with different cores. In the mix we have to included the diffent models, where there are several for each brand and before you know it you a MESS!
I am thinking over two decades ago, I should have dug a hole and through my computers in it and just became a farmer
|
|
|
|
|
Rocky Moore wrote: Over the last three weeks I have dug through tons of information trying to what works with what, what is just overpriced and what is garbage. Additionally, what will work with Vista or at least to a point.
I'm waiting for Quad Core processors to come out before I build my next machine!
Dave Kreskowiak
Microsoft MVP - Visual Basic
|
|
|
|
|
Dave Kreskowiak wrote: I'm waiting for Quad Core processors to come out before I build my next machine!
Same here. I'm also planning to wait until mid nextyear to see if the architecture changes AMD is releasing with it's quadcore design will surpass intel again.
|
|
|
|
|
Yeah, I am figuring once Vista settles after the first of the year, I will probably get a new high performance machine for development and give this to the wife. Hope I getting this one running by then
|
|
|
|
|
Rocky Moore wrote: Was amazed to see some MBs did not even come with LPT ports since one of my printers still only works via LPT.
PS2, COM, LPT, and Game ports have been legacy interfaces with no new hardware for years. The shedding of the ports has been starting on desktop boards for at least a year. Laptops have been shedding PS2 ports for years. Paradoxally those are the ports with the greatest desktop longevity.
Rocky Moore wrote: In the old days, you needed RAM, you purchased some of the speed you needed and presto it worked. Now it depends on vendor, volts and other things.
Unless you're having wierd compatability issues (or overclocking) none of these should matter. All DDR1 runs at the same voltage, all DD2 at the same voltage. Matched sets are basically marketing BS other than the fact that modern cpus use twin sticks to double bandwidth, which has happened in the past as well.
Rocky Moore wrote: Then there is the different CPU socket types and chip sets, along with different cores. In the mix we have to included the diffent models, where there are several for each brand and before you know it you a MESS!
You had diffent cpu types and sockets every few years in the past as well, along with mobos that had the same socket but didn't support chips beyond a different rev. Aside from the fact that AMD started designing it's own sockets (initially to avoid playing catchup with intel) nothing's changed.
|
|
|
|